Home
Products
Preparation Equipment
Processing Equipment
Packaging Equipment
Auxiliary Equipment
Laboratory Equipment
Bottled production line
News
Company Information
Industry Information
Exhibition Information
Sales Network
Partners
International sales network
About Tianhe
Company Profile
Enterprise culture
Qualification Honor
Contact Us
Online message
Language
简体中文
English
CFDA strives to improve the level of drug safety supervision
On May 13, the fifth annual meeting of the Drug Information Association (DIA) with the theme of "patient care and drug safety" was held in Beijing. Yin Li, deputy director of the State Food and Drug Administration, said at the meeting: "The Chinese government attaches great importance to drug safety and established the State Food and Drug Administration in this institutional reform. The purpose is to optimize regulatory resources and strengthen system risk prevention and control., Comprehensively strengthen food and drug supervision." Yin Li pointed out that we will reform and improve the drug safety supervision mechanism, scientifically divide the central and local drug supervision powers and responsibilities, content and procedures, and form a clear power and responsibility, reasonable division of labor, and legal protection
2013
05-16
Automatic tablet press installation, commissioning and disassembly
Installation, commissioning and disassembly of the full-automatic tablet press 1 Preparation before installation 1. The tablet press is installed on a firm wooden workbench (it can also be installed on a cement table) and fixed with three M12 anchor screws. The height of the work table to the ground is about 600mm (by hand, easy to operate). In order to facilitate disassembly and repair, there should also be a hole with a diameter of about 35mm on the wooden workbench corresponding to the position of the lower punch core rod. 2. Connect the motor to the ground wire before connecting the motor power supply to ensure safety. Remove the V-belt, turn on the motor power, and start the motor to observe whether the rotation direction of the motor is correct (motor shaft
05-14
Brief description of die installation for tablet press
Brief description of die installation of tablet press 1. First clean the machine and die. 2. Apply enough grease to other parts of the upper punch except the punch, and place the upper punch in the hole of the upper punch plate with the position of the keyway at the installation position of the punch die. 3. Lift the upper die a little and insert the middle die into the upper punch. (It is recommended to wrap the upper punch with plastic film before closing the middle mold to facilitate the adjustment of the gap in the following operations). 4. Align the middle punch hole, use the upper punch to introduce the middle die into the middle punch hole, tap the upper punch tail lightly to make the middle die enter the punch hole> 1/3, remove the upper punch, and punch the copper rod from the upper punch
05-12
Tablet press mold effervescent tablets sticky punch solution
After Teflon coating, the adhesive punching solution for effervescent tablets of tablet press die has the following characteristics: 1. non-tackiness 2, heat resistance 3, sliding 4, moisture resistance 5, wear resistance 6, corrosion resistance, chemical properties, insulation, high and low temperature resistance, self-lubrication, surface non-tackiness, non-combustibility, physical properties: application of PTFE (polytetrafluoroethylene): 1. Application of polytetrafluoroethylene (PTFE) in construction 2. Application of polytetrafluoroethylene (PTFE) in anti-corrosion performance 3. Application of polytetrafluoroethylene (PTFE) in electronic and electrical fields
05-02
RP200/RP300 Powder Forming Machine
Many pharmaceutical manufacturers in the purchase of carbon powder tablet press, do not know how to distinguish, or to buy what is better! Below by Shanghai Tianhe Pharmaceutical Machinery Co., Ltd. for you to introduce my factory production of RP200/RP300 powder molding machine, you are welcome to inquire! RP200/RP300 rotary powder forming machine is a new product successfully developed on the basis of digesting and absorbing similar models at home and abroad, combined with the company's rich experience in tablet press manufacturing. It is widely used in electronics, ceramics, magnetic materials and other industries to press all kinds of powder materials. 1. Metal components: no
04-23
Professional service team answers